Quality Clauses

Author: CC

Sep. 23, 2024

Consumer Electronics

Quality Clauses

Purchase Order Quality Clause Standard Requirements for Hawkesbury Canada

A000 - QUALITY CLAUSES NOT REQUIRED

Non-shippable items, for Dart Aerospace internal use only.

Check now

A001 - STATISTICAL PROCESS CONTROL

A002 - FABRICATION INSPECTION SYSTEM (FIS) FAR21.303

The supplier&#;s shall maintain a FIS in compliance with the requirements of FAR 21.303 (h). The FIS shall be approved and subject to audit by FAA, or its representative at any time.

A003 - QUALITY SYSTEM SURVEILLANCE

As a DART AEROSPACE supplier, the Seller's "Quality Control System" shall be subject to surveillance by DART AEROSPACE.

A004 - FAA-PMA /TSO

As a DART AEROSPACE supplier manufacturing an article or component for which DART AEROSPACE holds Supplemental Type Certificates (STC), your inspection system shall be subject to inspection by DART AEROSPACE at a level commensurate with criticalness of the article or component.

A005 - RIGHT OF ENTRY

Allows DART AEROSPACE, its customers and regulatory agencies the right of access, through prior notification, to determine and verify the quality of work, applicable quality records and materials at all applicable area of all facilities, at any level of the supply chain, involved in the order.

A006 - REQUIREMENTS FOR AIRWORTHINESS CERTIFICATION

Conformity Certification is required for articles specified on this purchase document. Include with each shipment, a true copy of Form One, Authorized Release Certificate, for Airworthiness. Foreign government equivalent to FAA Form -3 is acceptable for imported articles.

A007 - FIRST ARTICLE INSPECTION (FAI) BY SELLER, (DOCUMENTATION MAINTAINED BY SUPPLIER)

FAI shall be performed on all new or revised production manufactured items by seller at seller's facility. Results shall be documented on a report identified as "First Article Inspection Report" (FAIR). The report will be maintained at the seller&#;s facility, and be available for review by Dart Aerospace when requested.

A008 - FIRST ARTICLE INSPECTION (FAI) BY SELLER, (DOCUMENTATION SENT TO DART AEROSPACE)

FAI&#;s shall be performed on all new or revised production manufactured items by seller at seller's facility. Results will be documented on a report identified as a "First Article Inspection Report" (FAIR). The identified first article unit and the FAIR will be sent to Dart Aerospace.

A009 - FIRST ARTICLE INSPECTION (FAI) BY DART AEROSPACE AT SELLER'S FACILITY

FAI and/or test shall be accomplished at the Seller's facility before the balance of order may be shipped. DART AEROSPACE will conduct or witness inspections and/or tests and the results will be on a report form identified as "First Article Inspection Report".

A010 - DART AEROSPACE SOURCE INSPECTIONS

Dart Aerospace inspection is required prior to shipment from your facility. Evidence of such inspection must be included in your packing documents accompanying each shipment. You must contact Dart Aerospace's buyer and establish verification arrangements and the method of product release. Drawings, inspection/test documents, and specifications, as applicable, covering material on this order shall be available for inspection at your facility.

A011 - DELEGATIONS -SUPPLIER VERIFICATION OF DART AEROSPACE PRODUCT

The supplier has met the requirements established by DART AEROSPACE quality organization for the verification of DART product.

A012 - CHEMICAL AND PHYSICAL TEST REPORTS

Each shipment must be accompanied by one (1) legible and reproducible copy of all chemical and physical test reports identifiable with materials ordered. The reports must contain the signature and title of the authorized representative of the agency performing the test and must assure conformance to specification requirements.

A013 - SHELF LIFE CONTROLLED MATERIAL; 80% SHELF LIFE REQUIRED AT RECEIPT

Time sensitive material shall be furnished with a minimum of 80% of its shelf life remaining at date of shipment. Shelf life duration, date of manufacture and date of expiration shall be listed on material certification.

A014 - SHELF LIFE CONTROLLED MATERIAL; 70% SHELF LIFE REQUIRED AT RECEIPT

Time sensitive material shall be furnished with a minimum of 70% of its shelf life remaining at date of shipment. Shelf life duration, date of manufacture and date of expiration shall be listed on material certification.

A015 - SHELF LIFE CONTROLLED MATERIAL; 60% SHELF LIFE REQUIRED AT RECEIPT

Time sensitive material shall be furnished with a minimum of 60% of its shelf life remaining at date of shipment. Shelf life duration, date of manufacture and date of expiration shall be listed on material certification.

A016 - PERSONNEL QUALIFICATION

Supplier shall ensure all employees performing quality sensitive tasks on Dart products are qualified to perform the task associated with the product and this information is available in their training records.

A017 - RAW MATERIAL IDENTIFICATION (AS APPLICABLE)

A. Sheet or Plate Stock -Metallic or Non-Metallic
Each sheet or plate shipped shall be identified by continuous stenciling, of sufficient size to be readily legible, applied by permanent ink or dye of contrasting color, non-injurious to metal surfaces and not soluble.
B. Rod, Bar or Tube -all shapes -1/2 inch cross section or larger
Each length of Rod, Bar or Tube shipped shall be identified at one end or by continuous stenciling, of sufficient size to be readily legible, applied by permanent ink or dye of contrasting color, non-injurious to metal surfaces and not soluble in cutting and coolant oils. If continuous, spacing between groups of stencil letters shall not exceed twelve (12) inches. Information shall include material type or designation, material specification and temper.
C. Rod, Bar or Tube -all shapes -Smaller than 1/2 inch cross section
Rod, bar or tube shipped shall be bundled together; each bundle containing materials from the same (manufacturing/heat treatment) batch, and shall be identified as follows: An adhesive label or identification tag shall be securely attached to each bundle. This label or tag shall be permanently marked to indicate material type or designation, material specification and temper.
D. Castings / Forging -Ferrous or Non-Ferrous
Material shipped shall be identified with the part number, "melt" number, heat treat lot (if applicable) and serial number (if applicable). Identification of parts shall be in accordance with applicable drawings/specifications. Where drawings or specifications do not define method of identification, such identification shall be effected in accordance with MIL-STD-130
E. Extrusions
Each length of extrusion shall be identified at one end or by continuous stenciling, of sufficient size to be readily legible, applied by permanent ink or dye of contrasting color, non-injurious to metal surfaces and not soluble in cutting and coolant oils. If continuous, spacing between groups of stencil letters shall not exceed twelve inches. Information shall include material type or designation, material specification, temper and heat lot number.

A018 - ELECTRICAL EQUIPMENT

Each shipment shall be accompanied by one (1) legible and reproducible copy of a certificate containing the signature and title of the person authorizing the release of product. The certificate shall contain the part number, specification to which they conform, and general characteristic. When the parts are serialized, serial numbers shall be included on the certification. Manufacturer will maintain test reports, specification conformation and general characteristics on-site and available upon request.

A019 - ELECTRICAL CABLES (WIRES)

Electrical cables shall be identified with the part number and manufacturing code. The spool, and Certificate of Conformance shall be identified per applicable standard/specification with the following information: standard / specification, size code, manufacturing year, country code (if applicable), and manufacturer.

A020 - NON-DESTRUCTIVE TEST/INSPECTION IDENTIFICATION

All parts found to be acceptable by non-destructive testing methods are to be so identified by placing the proper acceptance test /inspection stamp on such acceptable parts. All parts found to be unacceptable are to be so identified by placing the proper withholding stamp on such defective parts. In those cases where NDT testing is being performed by a lower-tier supplier and his acceptance stamp is obliterated by further processing a copy of the lower-tier's certification must accompany shipment to DART AEROSPACE.

A021 - DART AEROSPACE PROCESSING

Seller shall assure that any process and or non-destructive test (NDT) requested on this purchase order shall be performed only by sources currently appearing on the DART AEROSPACE's "List of Approved Vendors" for the specific type of work to be conducted.

A022 - APICAL PROCESSING

Seller shall assure that any process work to be performed on Apical design and/or Part numbers by the Seller or its suppliers shall be performed only by sources noted in the latest published Apical Document Number MPP-120. MPP-120 Sources were used shall be submitted with AS First Article Inspection Report and as requested by Dart Aerospace.

A023 - IDENTIFICATION OF &#;DANGEROUS GOODS&#;

A &#;Dangerous Goods&#; decal must be applied to the outer container of the item being shipped and to the associated shipping document (shipper). Also, one copy of the applicable MSDS sheet must be provided with each shipment.

This is in addition to federal & provincial requirements noted in IATA & DOT CFR. It does not relieve the supplier of their responsibility to comply with any marking & labeling requirements set forth in the IATA & DOT CFR or any other legal documentation that may apply to this shipment.

A024 - PROCESS CERTIFICATIONS

Each shipment shall be accompanied by one (1) legible and reproducible copy of a certificate that must include the signature and title of the person authorizing release of product certifying all processes used, such as heat treating, welding, NDT, surface preparation and treatment, etc. The certificate shall include the processing used, the specification to which they conform and the name of the agency that performed them if other than the seller (i.e. sub-vendor). When the parts are serialized, serial numbers shall be included on the certification.

A025 - CERTIFICATE OF CONFORMANCE

Each shipment shall be accompanied by one (1) legible and reproducible copy of a Certification Document (Certificate of Conformance, Shipper, Packing List, etc.) that includes the identification (signature, electronic signature, stamp, etc.) of the person authorizing release of product assuring the items ordered were produced in accordance with and conforming in all respects with all applicable requirements set forth in Buyer's Standard Purchase Order Terms and Conditions and/or its contract with Seller, including specifications, drawings, revision, marking requirements, physical item identification and electrical characteristics when applicable. When the parts are serialized, serial numbers shall be included on the certification.

A026 - CERTIFICATION OF MATERIAL CONFORMANCE

A027 - FLAMMABILITY TEST

Test reports showing actual results of flammability test which meet the requirements of FAR 25.853(a) and signed by a responsible party shall accompany this shipment.

A028 - FLAMMABILITY TEST

Flammability Test reports showing actual results of flammability test(s). Reports must show Fire Worthiness resistance shall be such that the requirements of FAR 25.853 (a), Amendment 25-116 (60-Second Vertical Bunsen Burner Test). Appendix F, Part I will be met, or the latest revision of the Aircraft Materials Fire Test Handbook (DOT/FAA/AR-00/12).

A029 - FLAMMABILITY TEST

Flammability Test reports verifying Smoke emission shall be such that the requirements of FAR 25.853 (d) Amendment 25-116. Appendix F, Part V will be met, or the latest revision of the Aircraft Materials Fire Test Handbook (DOT/FAA/AR00/12). Reports must include a brief description of the sample and mounting.

A030 - FLAMMABILITY TEST

Flammability Test reports verifying Heat release capability shall be such that the requirements of FAR 25.853 (d), Amendment 25-116. Appendix F, Part IV will be met, or the latest revision of the Aircraft Materials Fire Test Handbook (DOT/FAA/AR-00/12). Reports must include a brief description of the sample and mounting.

A031 - FLAMMABILITY TEST

Flammability Test reports showing actual test results of flammability tests which meet the requirements of FAR 25.856 (a) and AC25.856-1 or the latest revision of the Aircraft Materials Fire Test Handbook (DOT/FAA/AR00/12).A032 - PUBLIC LAW 101-592 FASTENER QUALITY ACT

Supplier (Distributor) Certification: A Certification shall accompany each shipment of fasteners/washers, containing the following, as a minimum:

The manufacturer lot number(s) with associates part number(s); Manufacturers name; DART AEROSPACE P.O. number; and a statement to the effect that the manufactures certification (required by the Section 7 of the "Law") is on file with the distributor.

Supplier (Manufacturer) Certification: A Certification in accordance with Section 7 of the "Law" shall accompany each shipment.

Packaging: Each lot shall be packaged in a manner that ensures there will be no co-mingling of like fasteners from different lots in the same container.

Identification: Each package shall be identified with the lot number, name of the parts, part identification number, P.O. number and name of fastener manufacturer.

A032 - DOCUMENT SPECIAL REQUIREMENTS

1. The supplier is requested to ensure all original conformity documents (C of C, -3) are packaged in the container with the finished products.

2. The supplier is requested to ensure a copy of all conformity documents (C of C, -3) are part of the shipping documents which arrive with packaged components.

A033 - STATEMENT OF CONFORMITY/TEST RECORDS FOR NAS, AN and MS FASTENERS

1. When supplier is the fastener manufacturer -Each shipment shall be accompanied by one (1) legible and reproducible copy of a certificate of conformance containing the signature and title of an authorized representative which stated that the fastener have been manufactured in accordance with requirements of the applicable NAS, AN, MS government approved Parts Standard and Procurement Specification; and the chemical / physical test reports required by the government approved Procurement Specification are on file with the manufacturer, and available for review by customer and /or government quality assurance representative upon request.

2. When the supplier is a distributor -Each shipment shall be accompanied by one (1) legible and reproducible copy of conformity to purchase order requirements. The statement of conformity as a minimum shall contain DART AEROSPACE P.O. number, packing slip number; a copy of applicable test records (chemical, physical, processes and NDT) required by the government approved Parts Standard and Procurement Specification are available, or are obtainable upon customer request. The statement of conformity must contain the name of the fastener manufacturer, and shall be signed and dated by an authorized representative.

A034 - INTER COMPANY SHIPPERS

When products are shipped from one Dart Aerospace facility to another, the certification log number of the product being shipped must be recorded on the shipping document.

A035 - OUT TIME REQUIREMENTS

Supplier must record the "out-time" of exposure sensitive material (pre-preg) on packing list.

A036 - PRIORITY DX-A1

Priority DX-A1; this is a rated order certified for national defense use. You are required to follow all the provisions of Defense Priorities and Allocations System regulation (15 CFR 350).

A037 - PRIORITY DO-A1

Priority DO-A1; this is a rated order certified for national defense use. You are required to follow all the provisions of the Defense Priorities and Allocations system regulation (15 CFR 350).

A038 - AS First Article Inspection (FAI) by Seller, (Documentation maintained by Supplier)

A FAI per AS shall be performed on all new or revised manufactured items by the seller or at the seller&#;s facility. Forms other than as identified in the Appendix of AS must contain all required and conditionally required information and use same field reference numbers. Report is to be maintained at seller&#;s facility and available for review at Dart Aerospace&#;s request.

A039 - AS First Article Inspection (FAI) by Seller, (Documentation sent to Dart Aerospace)

A FAI per AS shall be performed on all new or revised manufactured items by the seller or at the seller&#;s facility. Forms used other than as identified in the Appendix of AS must contain all required and conditionally required information and use same field reference numbers. The report will be sent to Dart Aerospace.

A040 - Notification of Quality Escape

Seller will report to Buyer if a product, article or part has been released from Seller or Seller's subcontractors or suppliers and subsequently found not to conform to the applicable design data.

A041 - Quality Management System

Supplier shall implement, document and maintain a Quality Management System in accordance with applicable requirements of AS series standards or ISO standard and additional requirements specified on Buyers contract or purchase order. The Quality Management system shall be appropriate to the products the Supplier designs, manufactures, repairs or sells and shall cover all activities concerned by Dart Aerospace contracts or purchase orders.

A042 - DART NOTIFICATION BY SUPPLIER

Supplier shall notify Dart of changes in product and / or process, change of supplier and changes of manufacturing facility locations.

A043 - Retention of Quality Documents

Quality documentation recorded and certifications must be maintained on file for a period of 10 years after final payment on the purchase order. After this time period, suppliers shall not destroy such records without the written approval of DART AEROSPACE.

A044 - Calibration of Equipment

All calibration services shall provide a certificate of calibration for each item calibrated. The certificate must include company legal information and logo, the date of calibration, listed uncertainties, calibration due date, model, serial number of the equipment used in the calibration and a statement that all equipment/standards used are traceable to the National Institute of Standards and Technology (NIST). The certificate must also include Dart Aerospace purchase order number, tool number, model number and serial number of the item calibrated and list those standards used, the general condition of the equipment, Pass or Fail indication, calibration chart (when required) and the technician&#;s signature.

A045- DISCLOSURE(S) OF EU and CALIFORNIA ROHS WEE, REACH/ PROP. 65

EU and California environmental rules and requirements must be declared and/or abided by; for all materials within this shipment. This includes recycling requirements, declarations of non-compliance and information thereof for products used in the manufacture and/or sold to the buyer of this Purchase.

A046 - CERTIFICATION OF SPECIAL PROCESSES AND ITS INCLUSIVE LINE ITEMS

If drawings and/or specifications listed in this purchase order require special processes at the seller or the seller&#;s sub-tier, these processes shall be documented, reviewed and approved by Dart Aerospace prior to production. Approval of special processes by Dart Aerospace does not absolve the supplier from supplying conforming product. These processes include, but not limited to, the following: bonding, brazing, casting, Analysis (DPA), dye penetration inspection, forging, heat treating of metals, painting, plating, pressure testing, magnetic particle inspections, radiographic inspection, soldering, ultrasonic inspection, welding, or any other process defined in the purchase order.

A047 - SUBMISSION & RESUBMISSION OF NONCONFORMING ARTICLES OR MATERIALS

Do not send nonconforming products or materials to Dart Aerospace without prior documented authorized by Dart Aerospace Quality Department, such as a waiver or concession. Nonconforming articles and/or materials returned by the buyer and subsequently resubmitted by the supplier shall bear adequate identification of such nonconformance, on the articles, materials, or applicable supplier&#;s records. The supplier shall provide evidence that the cause of the nonconformance was corrected and that actions were taken to preclude and reoccurrence.

A048 - COUNTERFEIT PARTS AVOIDANCE, DETECTION, MITIGATION, AND DISPOSITION PROGRAM

Supplier shall have a counterfeit parts avoidance, detection, mitigation, and disposition program meeting the requirements of Aerospace Standard ASD or equivalent. Supplier shall only deliver authentic components, devices, pieces, material, modules, assemblies, subassemblies, goods, etc. that are manufactured by or obtained from original equipment manufacturers (OEMs), original component manufacturers (OCMs), or authorized distributors. Supplier shall make available to Dart Aerospace documentation that authenticates and provides traceability of the Parts to the applicable OEM or OCM.

A049 &#; SUPPLIER AWARENESS

Supplier shall ensures that its personnel are aware of their contribution to product or service conformity, their contribution to product safety, and the importance of ethical behavior.

Purchase Order Quality Clause Standard Requirements for San Diego, CA

Q001 - CONTROL OF SUB-TIER SUPPLIERS

The supplier, as the recipient of the PO or Contract, is responsible for meeting all PO/Contract specified technical and quality requirements, whether the supplier performs, the work or the work is performed by the supplier&#;s sub-tier sources. When the supplier uses sub-tier sources to perform work on products and/or services scheduled for delivery to Dart Aerospace, the supplier shall include (flow-down) on Purchase Orders of Contracts, to their sub-tier sources, all of the applicable technical and quality requirements of the Dart Aerospace P.O. or Contract, including, when applicable the requirements to document and control &#;key characteristics&#; and/or &#;key processes&#;, and to furnish certifications and test reports required by the applicable P.O. Quality requirements.

Q002 - QUALITY MANAGEMENT SYSTEM

Suppliers shall implement, document, and maintain a Quality Management System in accordance with one or more of the standards listed below. Dart Aerospace reserves the right to audit, review, and approve the supplier&#;s Quality Management System.

AS
AS
AS
ISO
14CFR 21.137
EASA 21

Note: Suppliers initially approved for use via certification (ISO, AS, etc.) must notify Dart Aerospace of any changes to that certification.

Q003 - PERSONNEL QUALIFICATIONS

Suppliers shall ensure all personnel performing quality sensitive tasks on Dart products are qualified to perform the tasks associated with the product and this information is available for review.

Q004 - CONFIGURATION MANAGEMENT

Suppliers shall maintain the proper identification and revision status of specifications, drawings, process requirements, inspection/verification instructions, and other relevant technical data.

Q005 - DART AEROSPACE PROCESSES

Dart Aerospace reserves the right to approve or specify any design, test, inspection plans, verification, use of statistical techniques for product acceptance, and any applicable critical items, including key characteristics.

Q006 - RIGHT OF ACCESS

Right of access shall be granted by the supplier to Dart Aerospace, their customers, US government, and/or regulatory agencies to the applicable areas of all supplier facilities, at any level of the supply chain, involved in the order and to all applicable records.

Q007 - SUPPLIER QUALITY RECORDS

The supplier shall maintain suitable inspection and test records to serve as evidence of conformance with specified requirements of the PO. Such records shall be legible and traceable to the product involved. These records shall be maintained for a minimum period of ten (10) years from the date of final manufacture or as stated otherwise in the contract.

Q008 - ETHICAL BEHAVIOR

The supplier is responsible for implementing a Code of Ethics within its organization; and assuring that all of its employees are aware of such requirement. Dart Aerospace has in place a Code of ethics which has been communicated to all employees.

Q009 - PRODUCT SAFETY

The supplier is responsible for the proper processing of the product, prior and during shipment to Dart Aerospace, to prevent any potential damage to the product. The supplier is also responsible that product safety is taken into account when processing the product for any testing and evaluation activities.

Q010 - SUPPLIER NOTIFICATION OF NONCOMFORMING PRODUCTS DELIVERED TO DART AEROSPACE

When the supplier has determined that nonconforming product(s) and/or Quality Escapes have been delivered to Dart Aerospace, the supplier shall notify Dart Aerospace within twenty-four (24) hours of the initial discovery. The supplier shall use receipt acknowledgment or other positive notification methods. The notification shall include the supplier name, Dart Aerospace PO/Contract number, part number and description, affected quantity and serial numbers (if known), dates delivered (if known), brief description of the nonconforming condition. The supplier shall provide evidence that the cause of the nonconformance was corrected and that actions were taken to preclude and reoccurrence

Q011 - MATERIAL REVIEW BAORD (MRB) AUTHORITY

Material Review Board (MRB) authority is not authorized on this purchase order.

Q012 - SHELF LIFE PROVISIONS

Dart Aerospace requires that all time sensitive material be shipped with a minimum of 95% shelf life remaining at date of shipment. Suppliers are required to provide shelf life duration, date of manufacturing, and date of expiration on the material certification.

Q013 - COUNTERFEIT/SUSPECTED UNAPPROVED PARTS (SUP)

Suppliers shall maintain a counterfeit parts, avoidance, detection, mitigation, and disposition program meeting the requirements of Aerospace Standard AS series or equivalent. The supplier shall only deliver authentic material and goods to Dart Aerospace. Suppliers shall make available to dart Aerospace documentation that authenticates and provides traceability of the parts to the applicable OEM.

Q014 - CHANGES AND APPROVAL

The supplier shall notify Dart Aerospace of any proposed changes in the design, fabrication methods, or processes previously approved by Dart Aerospace and/or Dart Aerospace&#;s customer, and obtain written approval of the changes from Dart Aerospace and/or Dart Aerospace&#;s customer. Changed articles shall be clearly identified and in a different manner from the previous articles. When the buyer procures a proprietary item, the supplier shall notify the buyer of changes. Other changes shall include: management, ownership, and manufacturing location(s).

Q015 - REQUIREMENT TO PROVIDE TEST SPECIMENS

Dart Aerospace reserves the right to designate requirements for test specimens for design approval, inspection/verification, investigation, or auditing.

Q016 - PRODUCT OR SERVICE CONFORMITY

The supplier shall ensure personnel processing orders or performing work affecting conformity to product or service are trained and aware of the importance of their activities associated with meeting the requirements of Dart Aerospace purchase orders.

Q017 - FOREIGN OBJECT DEBRIS/DAMAGE (FOD)

The Supplier shall assure that that devises, components and materials delivered under this contract are free of Foreign Object Debris (FOD). The Supplier shall employ general prevention practices to keep FOD, large or small, from the product and packaging. FOD contamination will be cause for rejection of material.

With competitive price and timely delivery, Dayin sincerely hope to be your supplier and partner.

Q018 - CALIBRATION PROVISIONS

Suppliers must meet at a minimum one of the following standards: ISO/IEC , ISO-1, ANSI Z540.3. All calibration certificates shall identify standards used and must be traceable to National Institute of Standards and Technology (NIST).

Q019 - CERTIFICATE OF CONFORMANCE

Suppliers shall provide evidence that the processes requested in this purchase order were performed by approved sources and such evidence retained on file per Q007 herein. Each shipment shall be accompanied by reproducible copy of the Certificate of Conformance (C of C) containing the signature of the person authorizing the release of the product for shipment to Dart Aerospace. When the product is serialized the serial numbers shall be included on the C of C.

Q020 - IDENTIFICATION OF &#;DANGEROUS GOODS&#;

A &#;Dangerous Goods&#; decal must be applied to the outer container of the item being shipped and to the associated shipping document (shipper). Also, one copy of the applicable MSDS sheet must be provided with each shipment. This is in addition to federal & provincial requirements noted in IATA & DOT CFR. It does not relieve the supplier of their responsibility to comply with any marking & labeling requirements set forth in the IATA & DOT CFR or any other legal documentation that may apply to this shipment.

Q021 - CERTIFICATE OF MATERIAL CONFORMANCE

Submit with each shipment one reproducible record of Actual chemical and or physical analysis and a certification of conformance to the applicable material specifications. The certification shall contain a list of the specification(s) including a revision letter(s), identification by Heat, lot, or Melt number, shall include the identification (signature, electronic signature, stamp, etc. of the person authorizing release of product certifying each material used to fabricate the items ordered in this "Purchase Order".

Q022 - FAA "STATEMENT OF CONFORMITY"

Products on this order are subject to mandatory Federal Aviation Administration (FAA) conformity inspection verification. When this conformity inspection is performed at supplier's facility, Dart Aerospace will complete FAA form -9 "Statement of Conformity" and notify the appropriate FAA representative. After completion of the FAA conformity inspection verification, supplier shall include one copy of FAA form with each conforming part shipped as evidence of inspection.

Q023 - ITAR/EXPORT REGULATIONS

WARNING: This purchase order may include documents which contain technical data, export of which is restricted by the INTERNATIONAL TRAFFIC IN ARMS REGULATIONS (ITAR). Disclosure to foreign persons without prior U.S. Government approval is prohibited. Violations of these Export Laws and Regulations are subject to severe Civil and Criminal penalties. SUPPLIER agrees to comply with all applicable U.S. export control laws and regulations, specifically including, but not limited to the requirements of the Arms Export Control Act 22 U.S.C. -, including the International In Arms Regulations (ITAR), 22 CFR 120-130 and Export Administration Act 50 U.S.C. app.2 -, Including Export Administration Regulations, 15 CFR 730-774; including the requirement for obtaining any export license or agreement, if applicable.

Q024 - RATED ORDERS

Rated orders for national defense use, the supplier shall follow all the requirements of the Defense Priorities and Allocations System regulation (15 CFR 700). If the attached Purchase Order is part of a Federal Government contract, then the following clauses apply (Q026). Priority DX-A1 and DO-A1 rated orders are certified for national defense use, DPAS regulations found in 15 CFR, Part 350 apply.

Q025 - EARLY SHIPMENTS

Do not ship prior to required date. Suppler shall notify Dart Aerospace of any changes in schedule.

Q026 - SHIP COMPLETE

Order must ship complete; partial deliveries will not be accepted without prior approval from Dart Aerospace.

Q027 - DISPUTES

Any disputes arising out of, or in connection with Dart Purchase Orders shall be governed by the laws of the State of California.

Q028 - THE FOLLOWING FEDERAL REGULATIONS ARE HEREIN INCORPORATED BY REFERENCE:

(1) 48 CFR 52.203-6 Restrictions on Subcontractor Sales to the Government
(2) 48 CFR 52.203-7 Anti-Kickback Procedures
(3) 48 CFR 52.209-6 Protecting the Government&#;s Interest when Subcontracting With Contractors Debarred, Suspended, or Proposed for Debarment
(4) 48 CFR 52.214-28 Subcontractor certified Cost or Pricing Data &#; Modifications &#; Sealed Bidding (OCT )
(5) 48 CFR 52.222-50 Human Trafficking
(6) 48 CRF 52.222- Person Trafficking
(7) 48 CFR 52.222-1 Notice to the Government of Labor Disputes
(8) 48 CFR 52.222-18 Certification Regarding Knowledge of Child Labor for Listed And Products
(9) 48 CFR 52.222-37 Employment Reports on Veterans
(10) 48 CFR 52.223-1 Bio based Product Certification
(11) 48 CFR 52.223-2 Affirmative Procurement of Bio based Products Under Service and Construction Contracts

Q029 - ELECTRONIC ASSEMBLIES, PARTS, AND EQUIPMENT

Suppliers shall default to Class 3 requirements if the class is not otherwise specified on the PO or other documents provided by Dart Aerospace.

Printed Circuit Board Assemblies PCBA&#;s will comply with IPC-A-610, Acceptability of Electronic Assemblies, unless otherwise specified.
Printed Circuit Board Assemblies PCBA&#;s will comply with IPC-J-STD-001, requirements for Soldered Electrical and Electronic Assemblies unless otherwise specified.
Electrical Cables Electrical cables shall be identified with part number and manufacturing code. The spool, and Certificate of Conformance shall be identified per applicable standard/specification with the following information: standard/specification, size code, manufacturing year, country code (if applicable), and manufacturer.
Electrical Wiring Harnesses Electrical wiring harnesses shall be assembled and tested in accordance with IPC 620 and the applicable &#;J&#; standard(s) that are associated with Harness&#;s assembly type.

Q030 - EVALUATING, APPROVING, AND MONITORING SUPPLIERS

Suppliers providing product or services to Dart Aerospace shall be initially evaluated to ensure products and services meet design data. All Dart Aerospace approved suppliers shall be monitored and evaluated based on criticality of product or service provided. Continued evaluation is scored based on quality, on-time delivery, and responsiveness.

Q031 - FIRST ARTICLE

Supplier shall perform a first article inspection in accordance with the requirements set forth in Purchase Order Information and/or Quality Clause requirements. Supplier shall forward one (1) copy of the first article inspection (FAIR) report to Dart Aerospace. FAIs shall be performed on all new and revised production manufactured items by supplier at supplier&#;s facility. Results of FAI&#;s will be documented on the FAIR, and maintained at the supplier&#;s facility and be available for review by Dart Aerospace when requested refer to Quality Clause Q007 for retention requirements.

Q032 - DISCLOSURE(S) OF EU and CALIFORNIA ROHS WEE, REACH/PROP. 65

Q033 - IDENTIFICATION, PRESERVATION, AND PACKAGING

All shipments to Dart Aerospace must be packaged to avoid damage and deterioration and must be shipped to the address specified on the PO unless otherwise noted. Packaging and packing shall be in accordance with good commercial practices unless otherwise specified on the PO. Parts shall not be intermingled unless otherwise specified. Each box or container shall be labeled and have as a minimum the following information: (1) Part number and revision, (2) PO number, (3) PO Line Item, (4) Quantity and (5) Manufacturer&#;s identification. Dangerous Goods shall be identified as required by DOT, IATA, and CFR regulations and standards, a decal must be affixed to the outside of the container as well as the shipping documentation. A Safety Data Sheet (SDS) shall accompany the shipping documentation and the shipment.

Note: Wood pallets fabricated outside of the United States must be treated for infestations and identified on the pallet in accordance with U.S. Regulations.

a. Individual Packaging Requirements:

All parts inclusive of this PO shall be packaged separate from one another to avoid damage and/or deterioration. Sheet foam, bubble wrap, or suitable paper wrapping shall be used.

b. Painted Parts Packaging and Handling:

Painted parts whether primed or finished shall be completely cured or outgassed prior to shipment and/or packaging so that re-wetting does not occur. Painted parts shall be individually wrapped for protection to keep them from chipping, being marred or scratched.

Q034 - FEDERAL REGULATIONS

Executive Order as amended, 41 CFR 60-1, Affirmative Action Obligations of Contractors and Subcontractors, 41 CFR 60-250, Affirmative Action Obligations of Contractors and Subcontractors for Disable Veterans and Veterans of the Vietnam Era, and 41 CFR 60-741, Affirmative Action Obligations of Contractors and Subcontractors for Handicapped Workers, are herein incorporated by reference.

Purchase Order Quality Clause Standard Requirements for Tallassee, AL

A001 - STATISTICAL PROCESS CONTROL

A002 - FABRICATION INSPECTION SYSTEM (FIS) FAR21.303

The supplier&#;s shall maintain a FIS in compliance with the requirements of FAR 21.303 (h). The FIS shall be approved and subject to audit by FAA, or its representative at any time.

A003 - QUALITY SYSTEM SURVEILLANCE

As a DART AEROSPACE supplier, the Seller's "Quality Control System" shall be subject to surveillance by DART AEROSPACE.

A004 - FAA-PMA /TSO As a DART AEROSPACE supplier manufacturing an article or component for which DART AEROSPACE holds Supplemental Type Certificates (STC), your inspection system shall be subject to inspection by DART AEROSPACE at a level commensurate with criticalness of the article or component.

A005 - RIGHT OF ENTRY

A006 - REQUIREMENTS FOR AIRWORTHINESS CERTIFICATION

A007 - FIRST ARTICLE INSPECTION (FAI) BY SELLER, (DOCUMENTATION MAINTAINED BY SUPPLIER)

A008 - FIRST ARTICLE INSPECTION (FAI) BY SELLER, (DOCUMENTATION SENT TO DART AEROSPACE)

A009 - FIRST ARTICLE INSPECTION (FAI) BY DART AEROSPACE AT SELLER'S FACILITY

A010 - DART AEROSPACE SOURCE INSPECTIONS

A011 - DELEGATIONS -SUPPLIER VERIFICATION OF DART AEROSPACE PRODUCT

The supplier has met the requirements established by DART AEROSPACE quality organization for the verification of DART product.

A012 - CHEMICAL AND PHYSICAL TEST REPORTS

A013 - SHELF LIFE CONTROLLED MATERIAL; 80% SHELF LIFE REQUIRED AT RECEIPT

A014 - SHELF LIFE CONTROLLED MATERIAL; 70% SHELF LIFE REQUIRED AT RECEIPT

A015 - SHELF LIFE CONTROLLED MATERIAL; 60% SHELF LIFE REQUIRED AT RECEIPT

A016 - PERSONNEL QUALIFICATION

A017 - RAW MATERIAL IDENTIFICATION (AS APPLICABLE)

A. Sheet or Plate Stock -Metallic or Non-Metallic Each sheet or plate shipped shall be identified by continuous stenciling, of sufficient size to be readily legible, applied by permanent ink or dye of contrasting color, non-injurious to metal surfaces and not soluble. B. Rod, Bar or Tube -all shapes -1/2 inch cross section or larger Each length of Rod, Bar or Tube shipped shall be identified at one end or by continuous stenciling, of sufficient size to be readily legible, applied by permanent ink or dye of contrasting color, non-injurious to metal surfaces and not soluble in cutting and coolant oils. If continuous, spacing between groups of stencil letters shall not exceed twelve (12) inches. Information shall include material type or designation, material specification and temper. C. Rod, Bar or Tube -all shapes -Smaller than 1/2 inch cross section Rod, bar or tube shipped shall be bundled together; each bundle containing materials from the same (manufacturing/heat treatment) batch, and shall be identified as follows: An adhesive label or identification tag shall be securely attached to each bundle. This label or tag shall be permanently marked to indicate material type or designation, material specification and temper. D. Castings / Forging -Ferrous or Non-Ferrous Material shipped shall be identified with the part number, "melt" number, heat treat lot (if applicable) and serial number (if applicable). Identification of parts shall be in accordance with applicable drawings/specifications. Where drawings or specifications do not define method of identification, such identification shall be effected in accordance with MIL-STD-130 E. Extrusions Each length of extrusion shall be identified at one end or by continuous stenciling, of sufficient size to be readily legible, applied by permanent ink or dye of contrasting color, non-injurious to metal surfaces and not soluble in cutting and coolant oils. If continuous, spacing between groups of stencil letters shall not exceed twelve inches. Information shall include material type or designation, material specification, temper and heat lot number.

A018 - ELECTRICAL EQUIPMENT

A019 - ELECTRICAL CABLES (WIRES)

A020 - NON-DESTRUCTIVE TEST/INSPECTION IDENTIFICATION

A021 - DART AEROSPACE PROCESSING

A022 - IDENTIFICATION OF &#;DANGEROUS GOODS&#;

A &#;Dangerous Goods&#; decal must be applied to the outer container of the item being shipped and to the associated shipping document (shipper). Also, one copy of the applicable MSDS sheet must be provided with each shipment. This is in addition to federal & provincial requirements noted in IATA & DOT CFR. It does not relieve the supplier of their responsibility to comply with any marking & labeling requirements set forth in the IATA & DOT CFR or any other legal documentation that may apply to this shipment.

A023 - PROCESS CERTIFICATIONS

A024 - CERTIFICATE OF CONFORMANCE

A025 - CERTIFICATION OF MATERIAL CONFORMANCE

A026 - DOCUMENT SPECIAL REQUIREMENTS

1. The supplier is requested to ensure all original conformity documents (C of C, -3) are packaged in the container with the finished products. 2. The supplier is requested to ensure a copy of all conformity documents (C of C, -3) are part of the shipping documents which arrive with packaged components.

A027 - STATEMENT OF CONFORMITY/TEST RECORDS FOR NAS, AN and MS FASTENERS

1. When supplier is the fastener manufacturer -Each shipment shall be accompanied by one (1) legible and reproducible copy of a certificate of conformance containing the signature and title of an authorized representative which stated that the fastener have been manufactured in accordance with requirements of the applicable NAS, AN, MS government approved Parts Standard and Procurement Specification; and the chemical / physical test reports required by the government approved Procurement Specification are on file with the manufacturer, and available for review by customer and /or government quality assurance representative upon request. 2. When the supplier is a distributor -Each shipment shall be accompanied by one (1) legible and reproducible copy of conformity to purchase order requirements. The statement of conformity as a minimum shall contain DART AEROSPACE P.O. number, packing slip number; a copy of applicable test records (chemical, physical, processes and NDT) required by the government approved Parts Standard and Procurement Specification are available, or are obtainable upon customer request. The statement of conformity must contain the name of the fastener manufacturer, and shall be signed and dated by an authorized representative.

A028 - INTER COMPANY SHIPPERS

When products are shipped from one Dart Aerospace facility to another, the certification log number of the product being shipped must be recorded on the shipping document.

A029 - OUT TIME REQUIREMENTS

Supplier must record the "out-time" of exposure sensitive material (pre-preg) on packing list.

A030 &#; Rated Orders

A031 - AS First Article Inspection (FAI) by Seller, (Documentation maintained by Supplier)

A032 - AS First Article Inspection (FAI) by Seller, (Documentation sent to Dart Aerospace)

A033 - Notification of Quality Escape

Seller will report to Buyer if a product, article or part has been released from Seller or Seller's subcontractors or suppliers and subsequently found not to conform to the applicable design data.

A034 - Quality Management System

A035 - DART NOTIFICATION BY SUPPLIER

Supplier shall notify Dart of changes in product and / or process, change of supplier and changes of manufacturing facility locations.

A036 - Retention of Quality Documents

A037 - Calibration of Equipment

A038- DISCLOSURE(S) OF EU and CALIFORNIA ROHS WEE, REACH/ PROP

. 65 EU and California environmental rules and requirements must be declared and/or abided by; for all materials within this shipment. This includes recycling requirements, declarations of non-compliance and information thereof for products used in the manufacture and/or sold to the buyer of this Purchase.

A039 - CERTIFICATION OF SPECIAL PROCESSES AND ITS INCLUSIVE LINE ITEMS

A040 - SUBMISSION & RESUBMISSION OF NONCONFORMING ARTICLES OR MATERIALS

A041 - COUNTERFEIT PARTS AVOIDANCE, DETECTION, MITIGATION, AND DISPOSITION PROGRAM

A042 &#; SUPPLIER AWARENESS

Supplier shall ensures that its personnel are aware of their contribution to product or service conformity, their contribution to product safety, and the importance of ethical behavior.

The supplier must apply Statistical Process Control (SPC) to this purchase order. A (Cpk) of 1.33 or greater is required. Each shipment must be accompanied with a signed copy of the applicable SPC Control Plan(s). The Control Characteristic listed in SPC Control Plan shall be approved by DART AEROSPACE Quality Assurance prior to commencing with production / processing.The supplier&#;s shall maintain a FIS in compliance with the requirements of FAR 21.303 (h). The FIS shall be approved and subject to audit by FAA, or its representative at any time.As a DART AEROSPACE supplier, the Seller's "Quality Control System" shall be subject to surveillance by DART AEROSPACE.

Top 5 Benefits Of Using Flutter App For Your Business

Flutter is one of the most sought-after mobile app development frameworks with an open-source environment. The benefits of the Flutter app for businesses cannot be overemphasized as the platform is used to develop startup-friendly, fully-featured 2D mobile apps for iOS and Android. Flutter app development has been gaining ground as one of the go-to options for App development.

Flutter is a portable and profoundly revolutionary UI toolkit from the search engine giant Google used for developing natively compiled and visually attractive apps in order to enhance the experience of users or customers. This new SDK (Software Development Kit) was launched after Android P.

What is Flutter?

Flutter is a cross-platform tool designed for creating intuitive iOS and Android applications using a single codebase via a reactive, modern framework, widgets, and tools. Flutter app development is based on the use of Dart programming language &#; which was launched in &#; which is object-oriented. Dart is a simple, client-optimized programming language that is used for writing app developing code for Flutter that runs on multiple platforms. It was developed by the search engine giant for building mobile, desktop, web, and backend applications.

Using this programming language to write apps makes the syntax looks somewhat similar to Java. The code is mostly combined using standard Android or iOS toolchains, which are typically used for specific mobile platforms.

This makes it even more convenient and provides much better performance, making it an excellent match for tech startups and businesses looking to invest in Flutter app development.

The central concept of Flutter revolves around the visual, platform, and interactive widgets, as every part of the UI is composed of a combination of different widgets. Each of these widgets defines one structural element or the other (like a menu or button), an aspect of the layout (e.g., padding), a stylistic element (such as a color scheme or font), etc.

Flutter doesn&#;t use OEM (Original Equipment Manufacturer) widgets. Still, it makes use of its off-the-shelf widgets, which look and works like a native app on iOS applications (Cupertino) or Android (Material Design). Developers or companies that are dedicated to Flutter App Development can use the cross-platform to create custom widgets. This makes Flutter App Development interesting, easy-to-learn for newbie mobile app developers.

Flutter is also making excellent progress in terms of popularity. The open-source framework has successfully made it to the top 100 software repositories based on GitHub stars at the time release preview 1 was officially announced in June . The framework has risen up the ranks as the benefits of the Flutter app for businesses are getting more appreciated. And Flutter is presently among the top 30 software repos.

The primary goal of the Flutter app project is to enable the simplified and rapid development of cross-platform mobile apps. The design of the mobile app is practically the same, irrespective of the operating system &#; i.e., iOS or Android &#; of the device.

This promising trend has shown no sign of slowing down any time soon because it keeps rising every day. The benefits of the Flutter app for businesses were so profound that thousands of Flutter applications have now found their way to app stores. One of the most used and prominent mobile applications that were built using the Flutter cross-platform framework is the Alibaba app, with over 50 million users.

Other big brands that use Flutter to create impressive, visually-appealing applications and enhanced app experiences for their numerous customers include:

Google Ads
Hamilton Musical
Google Greentea

Flutter App Development has become a very serious competitor to React Native as well as to native application development.

Benefits of Flutter App for Businesses

The following are some of the benefits of the Flutter app for businesses:

1. Faster Code Writing

For app developers, Flutter means more dynamic and faster mobile application development. Users can make immediate changes in the code and see the result almost instantly in the mobile app. This is the famed &#;Hot Reload&#; everyone talks about, which typically takes only milliseconds and helps Flutter app development teams fix bugs, add features, and even experiment faster. This is just one of the things that top app developers love about Flutter.

&#;Hot reload&#; is also very comfortable, especially when it comes to developer-designer cooperation any time app developers want to experiment or improve the look of a mobile application so that they can check the effects immediately or without delay. In other words, with Flutter, your mobile app development team can work together with your tester or designer on the UI, making quick changes, and seeing the outcome immediately.

Most types of code adjustment or changes can be swiftly hot reloaded, though a handful of list changes may require a full restart. But in the case of native application development, the project has to be rebuilt from scratch and may even take much more time, and time is money. You will have to wait for every single change, which may take several minutes.

2. Backed Heavily by a Large Community Support, Courtesy of Google

As mentioned earlier, Flutter is the brainchild of search engine giant Google, which is entirely free. And everyone knows how consistently supportive the tech giant can be when it comes to technologies or platforms under them with frequent updates and issue fixes.

And since the introduction of this powerful and intuitive cross-platform development framework, Google has pulled out all the stops to provide constant support to upcoming Flutter mobile application developers. Since then, the Flutter app development community has been growing from strength to strength.

The 25k GitHub is more than enough proof of the growing popularity of the Flutter cross-platform framework. Google organizes several events, helping both startups and established businesses to catch up, discuss, or learn how the Flutter app help to grow businesses. Google also looks into bugs encountered by mobile app developers and how they can be fixed.

Therefore, if your business apps are built using Flutter, you have nothing to worry about when it comes to developer support as well as consistent upgrades. Google, your beloved search engine, is more than capable of taking care of it.

3. An Excellent Choice for Advanced UI

The Flutter software renders every part of the interface by using an internal graphics engine known as Skia, i.e., the same used in Mozilla Firefox, Google Chrome, Sublime Text 3. This incredibly fast and well-optimized software allows Flutter to behave far more different than most other mobile application development frameworks.

Using Flutter is somewhat synonymous with writing code for a game. Right from the operating system, you will come across a blank canvas, and every UI element is drawn by application.

The Flutter app development team has put in extraordinary work to recreate Apple Design System elements and Material UI components internally. As might be expected, users can make or create their own components, and this is the aspect where Flutter truly shines.

Creating visually-appealing custom UI elements is relatively straightforward, and they can work seamlessly on both iOS and Android. This makes the Flutter cross-platform framework an excellent choice for mobile applications with highly advanced and custom UI designs.

4. Access to Device Features

One of the primary reasons why a lot of people are scared of cross-platform solutions has to do with issues with seamless access to native features. After all, what makes your mobile app stand out may include haptic feedback, GPS, the usage of the camera, etc. But you can get all these features when you build your mobile application with Flutter.

You may have to set up Android or/ and iOS code in Java/Kotlin or/and Objective-C/Swift. And then send data to Dart &#; i.e., the primary programming language used in developing Flutter &#; via a special or unique mechanism known as platform channels.

The Flutter core team and the community as well as prepared channels for the majority of the native functionalities of your smartphones so that you do not have to write them on your own. Channels are waiting for users that want to make use of the native library, which is not too popular.

5. Enhanced Time-to-Market Speed

Flutter app development framework functions faster than all its alternatives. One of the immense benefits of the Flutter app for businesses is that it requires at least two times fewer working hours to develop compared to the same mobile application developed separately for iOS and Android.

The primary reason for this is simple: there is no need to write any platform-specific code in order to achieve the result you desire in your mobile application. A 2D-based UI can be readily implemented in Flutter without necessarily interacting with a native app counterpart.

Moreover, Flutter offers a declarative API for creating UI, which significantly boosts the mobile application&#;s performance. This is even more evident when it has to do with visual adjustments.

These five benefits mentioned above about Flutter app development are not the only ones because Flutter has many other advantages such as:

Its ability to provide better user experience via the use of third-party integration
Native codes
The exploration of native features with Software Development Kit (SDK)
Native performance
Flexible and highly expressive UI
Single code for front end and back end
Perfect for a minimum viable product (MVP)
An open-source project
Availability of custom, animated UI
Ability to go way beyond mobile

Is There Anything Holding Flutter App Developers Back?

Mobile app developers that build native iOS and Android apps may be a bit put off by the need to learn Dart, which is yet another programming language. This is why most employers looking to hire a team of Dart developers to help them create their Flutter applications may encounter staffing issues because only a handful of mobile app developers out there know or understand Dart programming language.

However, because Dart programming language is very easy to learn compared to other programming languages, a serious mobile app developer should not find it difficult to pick up Dart as it will be an added advantage to the developer.

The unique features of the Dart programming language are very similar to Java. The similarities between Java and Dart enable app developers to make quick and easy shifts. Flutter is undoubtedly a much better option for app developers because of its relative ease of usage, astounding editorial integrations as well as the availability of better widgets.

But then, if you are into developing games or you require a mobile application that is loaded with several device-specific functions, Flutter may not be the right platform for you or your business.

Most doubts about Flutter app development are as a result of its novelty. Some mobile app developers believe that Flutter could not be used for building highly complex commercial mobile applications. So it is more suitable only for prototyping or building simpler applications.

However, when you browse the internet, you will come across several success stories about Flutter app development, especially those in production. You should also take the time to browse through the numerous list of mobile applications built with Flutter.

You will also come across articles that detail how the Flutter app help to grow businesses around the world.

So, is Flutter good for your business? By all means, because the benefits of the Flutter app for businesses far surpass any disadvantage, you may have heard. This implies that you can go full steam and invest in Flutter app development.

You need to also perform a lot of research to learn how the Flutter app help to grow businesses. The benefits of the Flutter app for businesses highlighted in this article show how much better it is than other cross-platform development frameworks.

Do not make the mistake of implementing different UIs for both platforms or implementing several platform-specific features. You may end up losing all the advantages of the framework. This is because you will inadvertently complicate your code and future development can become extremely problematic

But investing in Flutter app development ensures you will get your mobile application faster, and faster mobile app development will save you a lot of money in the long run. It will also validate your Minimum Viable Product (MVP) idea quicker than you think or expect.

For more information, please visit OEM Dart Board Supplier.

Comments

All Comments (0)

Three-Phase Power: What It Is and the Benefits It Brings

Video Wall Operational Efficiency: LED vs. LCD Solutions

Guest Posts

If you are interested in sending in a Guest Blogger Submission,welcome to write for us!

Your Name:(required)

Your Email:(required)

Subject:

Your Message:(required)

0/2000